Power Trowel Accessories

NORWIT.PL stocks power trowel accessories primarily from Husqvarna Construction, Enar and Toolsa, complemented by Barikell fittings for ride-on machines. The range includes double-sided trowel pans in 600, 900 and 1200 mm sizes, blades (combi, finishing, float) in sets of 4, and seats and transport dollies for ride-on power trowels. The assortment covers single-rotor, twin-rotor and self-propelled (ride-on) machines.

A trowel pan is a round steel disc mounted underneath a power trowel's blades that smooths the concrete surface without leaving edge marks — it's used mainly on the first pass over fresh concrete. Blades, also called trowel wings, are metal fins fitted directly to the spindle that compact and smooth the surface over subsequent passes, working at an angle of 5–25 degrees to the floor. The pan goes on for fresh concrete, and blades take over as the surface starts to set, usually across 2–3 successive troweling stages.

A double-sided pan for an Enar TIFON power trowel is matched to the spindle diameter — NORWIT.PL offers 600, 900 and 1200 mm variants, matched to the corresponding TIFON models. Once one side wears out, the pan can be flipped over and the other side used, extending the fitting's service life by up to twice as long. Before buying, it's worth confirming the exact power trowel model and spindle diameter on the product page, since a pan of the wrong size won't mount correctly.

Combi (combination) blades combine initial troweling and finishing in a single blade — a universal choice for typical concrete slabs, with a pitch angle usually of 5–15 degrees. Float blades have a wider, flatter surface and a low angle under 10 degrees — they're used to move and spread the mix over fresh concrete before the actual troweling begins. Finishing blades work at the steepest angle, up to 25 degrees, giving the surface its final sheen and hardness on the machine's last pass.

Trowel blades wear down at the working edge, and the rate depends on the hardness of the concrete and the number of hours worked — under intensive use, replacement can be needed every 100–200 hours, while occasional use might only mean once a season. Signs it's time for new blades include a rounded edge, a drop in finish quality (streaks, unevenness), or needing 1–2 extra passes to achieve the same result. Checking blade thickness regularly, every few jobs, helps avoid damaging the pan.

The Barikell ride-on power trowel seat at NORWIT.PL is offered as a single fitting shared by the MK8-90 and MK8-120 variants — they differ mainly in the working width of the pan (roughly 90 and 120 cm respectively), not in the seat platform's construction. The seat mounts to the same support frame using 2–4 bolts in a standard hole spacing. Before ordering, it's worth confirming the machine's production year on the product page, since older units may have used a different frame variant.

A transport dolly for a power trowel is used to move heavier ride-on power trowels between work areas without starting them up — machines of this type typically weigh several hundred kilograms, so transporting them on wheels makes site logistics much easier. The Barikell dolly at NORWIT.PL is shared between the MK8-90 and MK8-120 variants, usually has 2–4 wheels and a platform matched to the frame width (roughly 90–120 cm). It isn't a universal fitting — it's matched to a specific model, because the wheel spacing has to correspond to the chassis width.

A double-sided pan mounts underneath the blade set of a single-rotor power trowel (one spindle, one set of 4 blades), usually secured with 3–4 clips or wing bolts spaced evenly around the disc. Before fitting it, check which side has already been used — the double-sided design lets you flip it over once one surface wears out. The pan goes on for the first pass over fresh concrete and comes off before troweling with the blades, once the surface starts to set — typically 1–2 hours after pouring.

When buying a new power trowel, it's worth putting together a basic blade set (usually 4 per spindle) in the combi variant right away, plus a spare set for replacement. Single-rotor machines benefit from a double-sided pan matched to the spindle diameter (600, 900 or 1200 mm), while ride-on power trowels need an operator seat and a transport dolly to make moving a machine weighing several hundred kilograms easier. Having a spare blade set on hand helps avoid downtime on site if something wears out.

Power trowel accessories — pans and blades — are designed around each manufacturer's own mounting pattern, so interchangeability between brands isn't the rule. Enar blades for the TIFON models use their own 4-hole mounting layout, and pans come in 3 sizes (600, 900 and 1200 mm) assigned to a given spindle series — Toolsa accessories can use a different hole spacing, sometimes by as little as a centimetre or so. The safest approach is to match fittings to the exact model listed on the product page, comparing the hole spacing and count beforehand.